Streamline your back-office operations. Discover eazmybiz, a smart documentation tool by Televers. Learn More

RF Cable Guide: Cable Types, Connectors, Loss and How to Order RF Cable Assemblies

Last reviewed: 6 November 2026

An RF cable assembly is only as good as its weakest detail. The wrong cable adds loss, the wrong connector won't fit, and a poor match causes high VSWR or PIM that hurts coverage. This guide helps you choose the right coaxial cable type, connectors, length and loss for your application: cable types from RG174 to 7/8" feeder, connector types (N, SMA, RP-SMA, TNC, BNC, 4.3-10, 7/16 DIN, QMA, MCX, MMCX), 50 vs 75 ohm, loss, VSWR and PIM basics, a selector table and an order checklist.

Televers supplies RF cables and custom-length RF cable assemblies in all common cable types and connectors from New Delhi. We are the authorized representative in India for RFS and Spinner, and we also stock and resell Times Microwave Systems products. See our RF cables

What is an RF cable assembly?

An RF cable assembly is a length of coaxial cable with an RF connector fitted on each end. It carries radio-frequency signals between radios, antennas, test equipment and modules. To pick the right one you need five things: cable type, connector type and gender at each end, impedance (50 or 75 ohm), length, and how much loss your link can accept.

Short assemblies are often called jumpers or pigtails. A jumper connects a radio to an antenna or a feeder; a pigtail usually has a connector on one end and a board-level connector or bare end on the other.

RF cable types: how to choose

Thinner cables such as RG174, RG178 and RG316 are very flexible but lose more signal, so use them for short runs inside equipment or for small antennas. Mid-size cables such as RG58, LMR-195, LMR-240 and LMR-400 suit antenna runs of a few metres upwards. 1/4" and 1/2" super-flexible and low-loss cables are used for base-station jumpers, and 7/8" feeder for long runs up a tower or across a DAS.

Thin cables: RG174, RG178, RG316

Small and very flexible. Good for GPS and IoT antenna leads, module wiring and test leads. RG316 handles higher temperatures. Loss is high, so keep runs short.

General-purpose: RG58

A common 50 ohm cable for radios, lab jumpers and short antenna runs. Easy to route, with moderate loss.

Low-loss LMR series: LMR-195, LMR-200, LMR-240, LMR-400

LMR cables from Times Microwave Systems are widely used for WiFi, cellular and GPS antenna runs. LMR-240 is a popular all-rounder; LMR-400 has much lower loss for longer runs but is thicker and stiffer.

1/4" and 1/2" super-flexible and low-loss cables

Super-flexible cables bend tightly, so they are used as jumpers at radios and antennas. Standard 1/2" low-loss cable has lower loss but needs a wider bend radius. Low PIM matters here, especially on cellular sites.

7/8" feeder

RF cable comparison table

Thick, rigid, very low-loss cable for main feeder runs from equipment to the tower top, and for DAS backbones. Usually joined to the radio and antenna with 1/2" jumpers.

Figures are typical. Always check the datasheet for the exact cable.

N is the rugged threaded connector used on antennas and outdoor equipment. SMA is the small threaded connector on modules, WiFi gear and test equipment; RP-SMA is its reverse-polarity version used on many WiFi routers. 4.3-10 and 7/16 DIN are large low-PIM connectors for cellular base stations. TNC is a threaded version of BNC, BNC is a quick bayonet connector, and QMA, MCX and MMCX are small snap-on connectors.

N type

Threaded, weatherproof-friendly and good to several GHz. Common on antennas, outdoor radios, DAS equipment and test gear.

RF connector types: how to identify them

Small threaded connectors. SMA is standard on RF modules, GPS receivers and test equipment. RP-SMA (reverse polarity) swaps the centre pin between male and female and is common on WiFi routers and access points. SMA and RP-SMA look alike but don't mate properly, so check the centre pin.

TNC and BNC

A male connector usually has a centre pin and the coupling nut; a female has the socket and the outer thread. (RP connectors reverse the pin.) Right-angle connectors help in tight spaces and reduce strain on ports. Specify gender and straight or right-angle for each end.

50 ohm vs 75 ohmr: 50 ohm is the standard for radio, cellular, WiFi, GPS and test equipment. 75 ohm is used for video, broadcast and CATV. Keep the whole link at one impedance: mixing 50 and 75 ohm cable or connectors causes reflections and high VSWR, and some connectors (such as BNC) look alike in both versions.

4.3-10 and 7/16 DIN

BNC is a bayonet connector: push and twist a quarter turn. Used on test equipment, video and radios. TNC is a threaded version of BNC that holds better under vibration and works to higher frequencies; it is common on GPS antennas.

QMA, MCX and MMCX

Large, low-PIM connectors for cellular base stations, remote radio units, antennas and DAS. 7/16 DIN is the long-established standard; 4.3-10 is smaller and lighter, and is now common on newer radios and antennas.

Male, female and right-angle connectors

QMA is a quick-lock, snap-on alternative to SMA, handy where space for a spanner is tight. MCX and MMCX are miniature snap-on connectors used on GPS modules, small radios and compact devices; MMCX is the smaller of the two.

Loss, VSWR and PIM basics

Loss (attenuation) increases with frequency and cable length. Within comparable cable designs, larger cables generally have lower loss. Compare exact cable datasheets at the same frequency and length. VSWR shows how well the cable and connectors are matched; closer to 1:1 is better. PIM (passive intermodulation) is interference created by poor or loose connections, and matters most on cellular base stations and DAS.

Working out your loss

Loss is quoted per metre (or per 100 m) at a given frequency. Multiply by your run length and add a small loss for each connector. Check the datasheet figure at your operating frequency, not at a lower one.

Keeping VSWR and PIM low

• Use the correct connector for the cable, fitted to the maker's instructions.

• Tighten connectors to the recommended torque; loose connectors are a common cause of PIM.

• Don't bend cables tighter than their minimum bend radius.

• Weatherproof outdoor connections.

• For cellular sites, specify low-PIM-rated cable assemblies with connectors matching the equipment, commonly 4.3-10 or 7/16 DIN. Confirm the assembly’s PIM specification.

Televers provides test reports for custom orders, on request.

RF cable selector table

Find your application in the table and use the row as a starting point. If your exact case isn't listed, send us your requirement and we'll suggest the right assembly.

How to order an RF cable assembly: checklist

Tell us the cable type, the connector and gender at each end (straight or right-angle), the length, the quantity and your application or frequency. If you're not sure, send the equipment models or a photo of the ports.

1. Cable type: for example RG316, LMR-240, 1/2" super-flexible.

2. Connector, end A: type, male or female, straight or right-angle.

3. Connector, end B: type, male or female, straight or right-angle.

4. Impedance: 50 or 75 ohm.

5. Length: and the tolerance you need.

6. Quantity.

7. Application and frequency: for example GPS, WiFi, cellular DAS.

8. Extras: heat-shrink, labelling, weatherproofing, test report.

9. Preferred brand: for example RFS, Spinner or Times Microwave Systems, if required.

Stock and delivery

Televers keeps some cables in stock, such as LMR-240, and builds custom-length assemblies to order. The minimum order quantity depends on the assembly. Send your requirement for a lead time.

Frequently asked questions

Which RF cable has the lowest loss?

Within comparable cable designs, larger cables generally have lower loss at the same frequency and length. Among common types, LMR-400, 1/2" low-loss and 7/8" feeder have much lower loss than RG174, RG316 or RG58. Check the datasheet at your frequency.

What is the difference between SMA and RP-SMA?

RP-SMA reverses the centre pin: an RP-SMA male has a socket instead of a pin. RP-SMA is common on WiFi routers. The two look alike but don't mate properly, so check the centre pin before ordering.

Which cable should I use for a GPS antenna?

For short runs, RG174 or RG316 with SMA, TNC, MCX or MMCX connectors. For longer runs, a low-loss cable such as LMR-240. Match the connectors to your antenna and receiver.

What is the difference between 4.3-10 and 7/16 DIN connectors?

Both are low-PIM connectors for cellular base stations and DAS. 7/16 DIN is larger and long established; 4.3-10 is smaller, lighter and common on newer radios and antennas. Use the one your equipment has.

Can I use a 75 ohm cable in a 50 ohm system?

It's not recommended. Mixing impedances causes reflections and high VSWR. Use 50 ohm cable and connectors for radio, cellular, WiFi and GPS, and 75 ohm for video and CATV.

Does Televers make custom RF cable assemblies in India?

Yes. Televers supplies custom-length RF cable assemblies in all common cable types and connectors from New Delhi. The minimum order quantity depends on the assembly. Send your requirement for a quote and lead time.

Do Televers RF cable assemblies come with test reports?

Test reports are provided for custom orders, on request.

Not sure which RF cable you need?

Televers is an RF and fiber connectivity supplier based in Janakpuri, New Delhi, shipping across India. We are the authorized representative in India for RFS and Spinner, and we also stock and resell Times Microwave Systems products. Custom RF cable assemblies are sourced from a vetted network of assembly partners.

• Who we are: Televers, an RF and fiber connectivity supplier.

• Where we are: Janakpuri, New Delhi, India. We ship across India.

• Brands: authorized representative in India for RFS and Spinner; stockist and reseller of Times Microwave Systems products.

• RF cable assemblies: all common cable types and connectors, in custom lengths. Built with brand cables and with other quality RF cables, sourced from a vetted network of assembly partners.

• Stock: some cables, such as LMR-240, kept in stock. MOQ depends on the assembly.

• Test reports: for custom orders, on request.

See the range: RF cables

About Televers

Send us your equipment or antenna models, or a photo of the ports, with the length and quantity, and we'll suggest the right RF cable assembly and send a quote with a lead time. Reach us on WhatsApp or through the contact form.

SMA and RP-SMA