Fiber Patch Cord Guide: Connector Types, UPC vs APC, Single-mode vs Multimode, and How to Order
Last reviewed: 02/11/2026
A fiber patch cord looks simple, but one wrong detail, such as the wrong connector, the wrong polish or the wrong fiber type, means a link that won't light up or a cord that damages the port it plugs into. This guide helps you identify what you have and specify exactly what you need: connector types (LC, SC, FC, ST, E2000, MU, MTRJ), UPC vs APC, simplex vs duplex, armoured cords, fiber types (OS2, OM2, OM3, OM4), jackets, loss basics, cleaning, a selector table and an order checklist.
Televers supplies fiber patch cords in all common connectors and fiber types from New Delhi, with simplex, duplex and armoured options in custom lengths. See our fiber patch cords
What is a fiber patch cord?
A fiber patch cord is a length of optical fiber cable with a connector on both ends. It links equipment such as switches, routers, OLTs, ONTs and patch panels. To pick the right one you need five things: connector type at each end, polish (UPC or APC), fiber type, simplex or duplex, and length.
Patch cords are used for short connections inside racks, between racks and from wall outlets to devices. Longer fixed runs use trunk or distribution cable, terminated at a patch panel, and the patch cord makes the final, changeable connection.
Patch cord vs pigtail: A patch cord has connectors on both ends. A pigtail has a connector on one end only; the bare end is fusion-spliced onto an installed cable inside a splice tray or termination box. Use pigtails to terminate cable, and patch cords to connect equipment.
Fiber connector types: how to identify them
LC is the small push-latch connector used on most SFP and SFP+ transceivers. SC is the larger square push-pull connector common in FTTH and GPON. FC screws on, ST twists on with a bayonet, and E2000 has a spring-loaded dust shutter. MU and MTRJ are older small-form connectors still found in some equipment.
LC, SC, FC and ST connectors
LC (Lucent Connector): Small form factor with a 1.25 mm ferrule and a latch like a phone plug. The standard for SFP, SFP+, SFP28 and QSFP duplex optics, and for high-density patch panels in data centres. Usually used as an LC duplex pair.
SC (Subscriber Connector): Square body, 2.5 mm ferrule, simple push-pull mating. Very common in FTTH, GPON and telecom distribution frames, and in older enterprise equipment. SC/APC (green) is the usual connector on GPON splitters and ONTs.
FC (Ferrule Connector): Round metal body with a threaded coupling nut that screws on. It holds firmly under vibration, so you still see it on test equipment, older telecom gear and some measurement setups.
ST (Straight Tip): Round metal bayonet connector: push in and twist to lock. Mostly found in older multimode enterprise and industrial networks.
E2000, MU and MTRJ connectors
Connector comparison table
E2000: Push-pull connector with a built-in spring-loaded shutter that protects the ferrule from dust and laser light. Popular with European telecom operators and in high-power or CATV applications.
MU and MTRJ: MU is a small 1.25 mm push-pull connector, like a miniature SC, used in some telecom and Japanese-standard equipment. MTRJ is a duplex connector with two fibers in one plastic ferrule, used on older multimode switches. Both are less common today, so send us a photo if you're not sure.
For multi-fiber links (8 to 24 fibers in one connector), see our MPO Cable Selector Guide
UPC connectors have a flat, slightly domed end face and are usually blue (single-mode) or beige/black (multimode). APC connectors are polished at an 8° angle and are green. APC reflects far less light back, so it is preferred for GPON, FTTH and CATV. Never mate a UPC connector with an APC connector.
Mating UPC to APC leaves an air gap between the fibers, which causes high loss and can damage both end faces. The colour of the connector body is the quickest check, but always confirm with the equipment datasheet. A cord can be UPC on one end and APC on the other (for example SC/APC to LC/UPC), which is common between a GPON splitter and an LC-based device.
More detail: Connectors and polishing: UPC vs APC
UPC vs APC: polish and colour code
Single-mode (OS2, usually yellow jacket) carries signals over long distances and is the default for telecom, FTTH and links between buildings. Multimode (OM2, OM3, OM4, OM5) suits short links inside buildings and data centres. Match the fiber type to the transceiver and to the cable already installed; never mix single-mode and multimode in one link.
Jacket colour conventions
Armoured: An armoured patch cord has a flexible steel tube under its outer jacket that protects the fiber from crushing, rodents and accidental damage, while staying about as flexible as a normal cord. Use it in exposed routes, under floors, in industrial sites, outdoor cabinets and tower installations. Armoured cords are available in the same connectors and fiber types as standard cords, in simplex and duplex.
LSZH vs PVC: LSZH (low smoke zero halogen) jackets give off little smoke and no halogen gas in a fire, so they are preferred in data centres, offices, hospitals and any enclosed space. PVC is cheaper and flexible, and is fine where building rules don't require LSZH. If unsure, ask for LSZH.
Typical reach (check your transceiver datasheet)
OS2 single-mode: yellow
OM2 multimode: orange
OM3 multimode: aqua
OM4 multimode: aqua or violet (erica violet)
OM5 multimode: lime green
Colours are an industry convention, not a guarantee, so check the print on the jacket.
Simplex vs duplex patch cords
Reach depends on the transceiver, not just the cord. As a rough guide, OS2 single-mode handles kilometres. For 10G, OM3 is commonly rated to around 300 m and OM4 to around 400 m, while OM2 is limited to much shorter distances. At 40G and 100G, multimode reach is shorter again. Always use the figure on the optic's datasheet.
More detail: Single-mode vs multimode fiber
Armoured patch cords and jacket types
A simplex cord has one fiber and one connector at each end. A duplex cord has two fibers, usually joined side by side, for equipment that transmits on one fiber and receives on the other. Most SFP optics need duplex LC. BiDi optics and many GPON connections use simplex.
On duplex cords, check that the transmit and receive sides cross over correctly (A to B). Most standard duplex cords are made this way; if your link does not come up, swapping the two connectors on one end is a common fix.
Insertion loss, return loss and cleaning
Insertion loss (IL) is how much light is lost through a connection; lower is better.
Return loss (RL) is how much light is reflected back towards the source; a higher number is better.
APC connectors give much higher return loss than UPC, which is why they are used for GPON and video. Dirty or damaged end faces are the most common cause of high loss. Televers provides IL/RL test reports with custom orders and on request.
Cleaning and handling: Inspect and clean every connector before you plug it in, even a new one. Use a one-click cleaner or lint-free wipes with fiber cleaning fluid, keep dust caps on unused connectors, and don't bend the cord tighter than its minimum bend radius.
- Never look into a connector or port that may be live.
- Clean both the cord and the port; a clean cord in a dirty port is still a dirty link.
- Don't pull the cord by its jacket to unplug it; hold the connector body.
- Coil spare length loosely and avoid sharp edges and tight cable ties.
Fiber patch cord selector table
Find your application in the table, then order what the row says. If your exact case isn't listed, send us the equipment or transceiver model and we'll specify it.
How to order a fiber patch cord: checklist
Tell us the connector and polish at each end, fiber type, simplex or duplex, length, jacket and quantity. If you're unsure about any of these, send the equipment or transceiver model and we'll fill in the rest.
1. Connector, end A (LC, SC, FC, ST, E2000, MU, MTRJ)
2. Connector, end B
3. Polish at each end (UPC or APC)
4. Fiber type (OS2, OM2, OM3, OM4)
5. Simplex or duplex
6. Standard or armoured
7. Jacket (LSZH or PVC)
8. Length (metres)
9. Quantity
10. Test report needed? (yes or no)
Stock and delivery
Because there are so many combinations, we keep only a few patch cords in stock. Small orders usually ship within 5 to 10 days; larger orders in 2 to 3 weeks, and very large orders can be delivered in phases.
Frequently asked questions
What is the difference between LC and SC patch cords?
LC is a small 1.25 mm connector with a latch, used on most SFP transceivers and high-density panels. SC is a larger 2.5 mm push-pull connector, common in FTTH, GPON and telecom frames. Pick the one that matches the ports at each end; an SC to LC cord links the two.
Can I connect a UPC connector to an APC connector?
No. UPC has a flat end face and APC an 8° angle, so mating them leaves a gap that causes high loss and can damage both connectors. Green connectors are APC; blue, beige or black are usually UPC.
Which patch cord do I need for a 10G SFP+ module?
Usually an LC to LC duplex cord. For SR (short reach) optics use OM3 or OM4 multimode; for LR optics use OS2 single-mode, UPC. Check the transceiver datasheet to confirm.
Which patch cord is used for GPON or FTTH?
Most GPON and FTTH connections use single-mode OS2 cords with SC/APC (green) connectors, usually simplex. Some devices use LC, so check the port.
What is an armoured fiber patch cord?
A patch cord with a flexible steel tube under the jacket for protection against crushing and rodents. Use it on exposed or industrial routes. Televers supplies armoured cords in simplex and duplex.
Does Televers supply custom fiber patch cords in India?
Yes. Televers supplies fiber patch cords in LC, SC, FC, ST, E2000 and other connectors, in OS2, OM2, OM3 and OM4, simplex, duplex or armoured, in custom lengths. Small orders usually ship within 5 to 10 days; larger orders in 2 to 3 weeks.
Do Televers patch cords come with test reports?
IL/RL test reports are provided with custom orders and on request. They are not supplied with stock cords.
Not sure which patch cord you need?
Televers is an RF and fiber connectivity supplier based in Janakpuri, New Delhi, shipping across India. We supply fiber patch cords in all common connectors and fiber types, sourced from a vetted network of assembly partners, along with Televers-branded MPO cables and RF cables, connectors, adaptors and attenuators.
Who we are: Televers, an RF and fiber connectivity supplier and authorized representative in India for global brands including RFS, Spinner and NetPoint.
Where we are: Janakpuri, New Delhi, India. We ship across India.
Fiber patch cords: LC, SC, FC, ST, E2000 and more; OS2, OM2, OM3 and OM4; simplex, duplex and armoured; custom lengths. Sourced from a vetted network of assembly partners.
Stock and delivery: a few cords in stock. Small orders usually ship within 5 to 10 days; larger orders in 2 to 3 weeks; very large orders can be delivered in phases.
Test reports: IL/RL reports with custom orders and on request.
About Televers
Send us your equipment or transceiver models, or a photo of the ports, and we'll suggest the right patch cord and send a quote. Reach us on WhatsApp or through the contact form.


